All products and services
1～30 item / All 42 items
-
Chip conveyor * Comprehensive catalog available
A chip conveyor that reliably discharges various types of chips and shavings! Coolant liquid purification unit also available.
last updated
-
Chip conveyor and coolant filtration device
Total coordination from cutting powder processing to coolant liquid filtration.
last updated
-
Processing of chips from castings, iron, aluminum, etc. Design and manufacturing of coolant systems.
We accommodate a wide variety of needs! We can conduct on-site surveys and meetings anywhere in the country. *Comprehensive catalog available.
last updated
-
Coolant primary filtration device "Magnet Separator (Comb Type)"
By improving sludge discharge, we will reduce the product defect rate and decrease the frequency of tank cleaning.
last updated
-
[Case Study of Microseparator] Settling Contaminants and Sludge
Before the installation of the microseparator, it was 74.2mg, and in just one month, it has already halved to 35.9mg!
last updated
-
Measures against valve burning and oil temperature rise in surface grinding machines due to oil purification.
This is an introduction to a case study on the introduction of micro-separators for measures against valve burnout and oil temperature rise.
last updated
-
Case Study of Micro Separator: Purification of Lubricating Oil for Fluid Bearings of Grinding Discs
Two MSR-200 micro separators have been installed, and a two-month trial will be conducted!
last updated
-
Improvement of direct pressure surge stirring type tank that cannot have additional partition boards installed.
This is a case study of introducing a micro separator into a direct pressure surge mixing tank where additional partition boards cannot be installed.
last updated
-
Improvement of cycle time and product accuracy through the purification of hydraulic operating oil.
Case study of micro separators! Measures have been taken to prevent the contamination of fine chips generated during grinding.
last updated
-
[Case Study of Micro Separator] Hydraulic and Lubrication Combined Flat Grinding Machine
After the installation of the microseparator, the oil analysis conducted two and a half years later showed no problems and was progressing smoothly!
last updated
-
[Case Study of Micro Separator Introduction] Labor-saving Management of Water Glycol in Casting Machines
After the installation of the microseparator, issues related to the properties of the water-glycol operating fluid are gradually being resolved!
last updated
-
[Case Study of Micro Separator] Utilization of Lubricating Oil Circulation in Injection Molding Machines
The analysis results demonstrated that the fuel in the fueling department is in a condition close to new oil, with no issues regarding viscosity or other factors.
last updated
-
Evaluation of the Cleaning Tank System and Company-wide Horizontal Deployment
The cleaning tank system prevents oil degradation! This is a case study of the introduction of a micro separator.
last updated
-
Case Study of Microseparator: Purification of Hydraulic Oil in Adverse Environments
After the measures were taken, we are maintaining a state of "almost no contamination from new oil"!
last updated
-
The overwhelming difference between bar magnets and micro separators (hydraulic and lubricating oil).
Case study of micro-separators! We had them experience the purification capability through a test adoption.
last updated
-
[Case Study of Micro Separator] Improvement of Cp Value through Purification of Operating Oil
The partition board was installed using the mounting bolts of the micro separator.
last updated
-
Data: Cutting Powder Transfer Machine TC-M
We would like to introduce the representative "TC-M type" that uses a magnet to transport chips.
last updated
-
Case studies of Magbar introduction
The introduction of the mag bar has reduced the defect rate due to scratches and the amount of chips accumulated inside the tank!
last updated
-
Efficient filtration of cutting and grinding coolant! Coolant filtration products.
Introducing products that can recover up to 95% of oil and efficiently collect sludge! *Catalog available.
last updated
-
Reduce defects caused by scratch marks! Liquid contamination removal and adsorption device.
【Zero Consumables】Strong magnets attract iron-based chips and capture contaminants in the liquid! Easily installable on various processing machines. *Materials with case studies are currently being distributed.
last updated
-
San-Esu Industry's 'Comprehensive Catalog' *Free Gift
A wide variety of chip conveyors for industrial machinery, coolant units, and various filtration devices are featured! A must-see for those involved in steel mills, machine tools, automotive, construction machinery, and shipbuilding!
last updated
-
Liquid Contamination Removal and Adsorption Device "MagBar"
Strongly adsorbs fine metal shavings from coolant fluid. Easy cleaning without dirtying your hands!
last updated
-
Micro separator
Micro separator
last updated
-
Magnetic Chip Conveyor
Effective in discharging chips generated during the processing of iron materials! Safe structure as the drive part is not exposed! 【Magnetic Chip Conveyor】
last updated
-
Coolant purification tank
Coolant purification tank
last updated
-
High Mag Scepter
High Mag Scepter
last updated
-
Cutting coolant filtration product - Spin Separator
Achieves a grease recovery rate of 90-95% despite its compact size!
last updated
-
[Case Study] Contamination Management of Hydraulic Oil and Lubricating Oil - Micro Separator
Reduced the amount of pollutants and eliminated abnormal sounds from the pump and malfunctions of the valve.
last updated
-
Self-Cleaning Coolant Tank System
It is applicable to all coolant tanks, regardless of the type of processing or coolant.
last updated
-
Cutting coolant filtration product - Magnetic chip conveyor
We achieve the removal of chips generated during all cutting processes.
last updated