ジャパンコントロールス 「Japan Controls Co. Ltd.」 東京本社 Official site

Extremely effective for detecting weld seams in pipe materials. If the pipe cannot be detected by color sensors or laser sensors, leave it to SND40.

★ It is possible to monitor programming, operation, and measurement results using a 10-inch touchscreen, and it can be used in combination with the customer's positioning device. ★ Depending on the pipe diameter, it can achieve a maximum of 300 revolutions per minute, with a plate feed speed of approximately 10 meters per minute, and it supports USB and Ethernet interfaces as well as various field buses, providing sufficient functionality to promote automation. For more details, please contact us or download the catalog.

Dedicated device for detecting steel wire cord defects in the tire manufacturing process.

★Compared to conventional X-ray inspection devices, this system is cost-effective and continuously records all data related to tire steel wire cord materials and splice sections. ★It is possible to stop the process based on abnormal part detection output and to discharge or repair the abnormal components. ★Adopted by many tire manufacturers worldwide, including Goodyear and Michelin, it has established sufficient reliability along with high detection capability. *For more details, please contact us or download the catalog!

Welding joints, defect detection devices, etc.

The product consists of a controller and a sensor unit, and the controller can connect up to two sensors. The measurement results (defects/dents or poor connection joints) are sent directly to the host PC via PLC, fieldbus, or RS232/Ethernet. !! For more details, please inquire or download the catalog !!

Detect the position of the weld joint and output a stop signal at any angle! Compatible with pipe diameters of 500mm! The operation screen is also available in Japanese!

In automotive parts such as stabilizers and steering shafts, automatic detection of weld seams is required, along with "positioning of the material" to stop the seam at a specified angle in preparation for the next bending process. This product is equipped with a function to output a stop signal at this specified angle. <Examples of use in the automotive field> ■ Stabilizer ■ Steering shaft ■ Seat frame ■ Drive shaft ■ Shock absorber ■ Suspension components ■ Door impact beam, etc. <Other features> ◎ Programming, operation, and monitoring of measurement results via a 10-inch touchscreen ◎ Compatible with existing positioning devices ◎ Printer, mouse, and keyboard can be connected to the control unit ◎ Rich interface options (USB, Ethernet interface, field bus: PROFIBUS, CONTROLNET, DEVICENET, INTERBUS, etc.) *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

Detects weld seams and outputs a stop signal at the specified angle! Supports pipe diameters up to 500mm.

In the manufacturing of long extended coil materials and other long materials (such as cables and wires), automatic detection of weld seams is essential. Additionally, for metal tube materials, cans, and drums, along with automatic detection of weld seams, "material positioning" is required to stop the seam at a specified angle in preparation for the next processing step. This product is equipped with a function to output a stop signal at this specified angle. 【Other Features】 ■ No influence from dust, dirt, rust, or oil on the surface ■ Can detect cracks and defects in butt welding ■ Programming, operation, and measurement result monitoring via a 10-inch touchscreen ■ Control unit can connect to a printer, mouse, and keyboard ■ Rich interface options (USB, Ethernet interface, field bus: PROFIBUS, CONTROLNET, DEVICENET, INTERBUS, etc.) *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

We will detect weld seams of narrow steel strips (both magnetic and non-magnetic). The width of the steel strip is 5-30mm, thickness is 0.2-4mm, and the transport speed is up to 5m/s.

The detection method of the Roland NS9N uses leakage magnetic flux and eddy current sensors, allowing detection regardless of whether the material is magnetic or non-magnetic. Until now, various methods such as induction and optical sensors have been used for seam detection, but it has not been easy to address unexpected issues such as gaps between the sensor and the metal surface or discoloration of the surface. The Roland NS9N can analyze not only geometric changes but also electrical and magnetic conductivity changes, thereby enhancing the reliability of the processing process. Additionally, the analog output can be directly connected to a PLC, facilitating smooth process control.

Weld joint defect detection device.

The product consists of a controller and a sensor unit, and the controller can connect up to two sensors. The measurement results (defects/dents or poor connections) are sent directly to the host PC via PLC, fieldbus, or RS232/Ethernet.

Welding seam detection device for pipes (up to 500mm in diameter), metal sheet coils, electric wires, and wires.

It is possible to monitor programming, operation, and measurement results using a 10-inch touchscreen, and it can be used in combination with the customer's positioning device. Depending on the pipe diameter, it can achieve a maximum of 300 revolutions per minute, with a plate feed speed of approximately 10 meters per minute, and it supports USB and Ethernet interfaces as well as various field buses, providing sufficient functionality to promote automation.