ジャパンコントロールス 「Japan Controls Co. Ltd.」 東京本社 Official site

Typical clean gas control in biopharmaceuticals, pharmaceuticals, and food and beverage processes.

- The stainless steel regulator is made of ASTM A479, with a body made of bar steel and all wetted parts. - The product uses a Jorlon diaphragm that is FDA certified and has proven USP Class 6 closure integrity. - There are threaded sections outside the wetted area, and the internal volume is minimized. - The diaphragm is fully guided at the top, and there are no threaded sections, cracks, or grooves in the wetted area. - The trim can be replaced while piped without disassembling the dome/spring chamber assembly. For more details, please download the catalog or contact us.

Supports various industrial use cases including food, beverages, healthcare, and pharmaceuticals.

★ The FB5CPM (inlet side/back pressure valve) and FB6CPM (outlet side/reduction valve) are air signal setting type sanitary pressure control valves, allowing users to change the set values remotely via a DCS or PLC using manual pneumatic pressure reducing valves or electro-pneumatic regulators. ★ This CPM series is an ideal choice for automatically maintaining the pressure set values of the valve for process set values or for settings that fully open the valve during rinsing, CIP, or SIP. ★ It is suitable for HTST/high-temperature sterilization, UHT/ultra-high-temperature sterilization, as well as heat exchangers, separation devices, bottling processes, and more. For more details, please download the catalog or contact us.

Control valve for sanitary processes. Suitable for pressure, temperature, flow rate, pH, or other displacement control.

★This stainless steel control valve has a body made of ASTM A351, CF3M, 316L cast material, and all wetted parts are made of ASTM A479 316L bar stock. ★The valve stem is integrated, and the stainless steel NAMUR yoke has sufficient structural strength with two extended PEEK guide bushings, regardless of the mounting orientation. ★The sliding parts of the valve stem and plug are located outside the wetted area of the stem O-ring at the top of the valve. ★The extended guide bushings provide additional retention in any mounting orientation, ensuring self-draining capability regardless of the installation direction. <Finish> Body: Standard: Internal wetted parts are mechanically polished to 0.8μm Ra, external surface is as-cast. Stem: Standard: Mechanically polished to 0.8μm Ra. For more details, please contact us or refer to the catalog.

3A certification, cavity-filling ball valve.

Product Overview - Connection Diameter: 1/2" ‒ 4" - Body Style: Three-piece - Pressure Rating: 6.9MPa WOG for 1/2" - 2", 4.14MPa WOG for 2-1/2" - 4" - Temperature Rating / WSP: 160℃ / 0.55MPa - Body/End Cap: Stainless Steel - Ball/Stem: Stainless Steel - Ball Seat: FDA Certified PTFE - Stem Packing/Seat: FDA Certified PTFE - Operation/Mounting Pad - Manual Locking Lever / ISO 5211 For more details, please contact us or refer to the catalog.

Compact, high purity, low pressure, low flow, back pressure regulator

★The robust valve body and metal trim are made of ASTM A479 316L stainless steel, with ASME BPE SF5 (0.5μm Ra electropolished finish) as the standard. ★The durable Jorlon diaphragm and TFM or PEEK sheets are all FDA certified and compliant with USP Class 6 materials. ★These components allow for strict continuous CIP/SIP processes if necessary. <Attached Documents> • Steriflow certificate, QC department signed compliance document - Material and heat number of each component listed - Surface finish - FDA/USP Class 6 - All thermoplastic and elastomer materials • Traceability - The serial number of each product can be traced back to the serial number and heat number in the integrated certificate For more details, please contact us or download the catalog.

Compact, high purity, low flow back pressure regulator

★The robust valve body and metal trim are made of ASTM A479 316L stainless steel bar stock, with ASME BPE SF5 (0.5μm Ra electropolished finish) as the standard. ★The durable Jorlon diaphragm and TFM or PEEK sheets are all FDA certified and compliant with US FDA regulations, as well as USP Class VI materials. ★These components allow for strict continuous CIP/SIP processes if necessary. <Attached Documents> • Steriflow Certificate, QC Department Signature Compliance Document - Material and heat numbers for each component - Surface finish - FDA/USP Class VI - All thermoplastic and elastomer materials • Traceability - The serial number of each product is traceable to the serial number, heat number, and material in the integrated certificate For more details, please contact us or download the catalog.

Compact, high purity, low pressure setting back pressure regulator

★The robust valve body and metal trim are made of ASTM A479 316L stainless steel bar stock, with ASME BPE SF5 (0.5μm Ra electropolished finish) as standard. ★Additionally, the durable Jorlon diaphragm and Teflon or PEEK sheets are all FDA certified and comply with USP Class VI materials. ★These components allow for strict continuous CIP/SIP processes if necessary. <Available Gases> • Air • Nitrogen • CO2 • Oxygen • Argon • Various mixed gases

Manual and automatic ball valves. General-purpose, high-performance, flange connection type. Various body materials and high-temperature specifications.

- Low-cost general-purpose fluid control products - Oil-free/water-free processing - For chlorine and anhydrous ammonia - Extended shaft bonnet - Fittings, limit switches, NACE specifications - Processing for oxygen gas - Fire shut-off - Gear-operated, automatic - Carbon and stainless steel API 607 fire test (standard) - ISO 5211 direct mount actuator pad - Fixed handle, tongue-and-groove seal - Mechanical packing - Easy maintenance during piping connection For more details, please contact us or download the catalog.

Simple structure, excellent performance. For liquids and gases. The products are self-operated, high flow rate, differential pressure type, vacuum, air load type, and pilot type.

- You will notice the differences between the Jordan valve and other companies' products, which is the sliding gate seat. - This noteworthy simple structure has excellent performance and features not found in traditional lift stem or rotary valves. - The sliding gate seat consists of two main components: a movable disk and a fixed plate with multiple orifices. - These components provide performance, reliability, and precision that are difficult to achieve with other valve styles. For more details, please contact us or download the catalog.

Precise control of liquid, gas, or steam flow. Providing reliable, high-performance solutions.

- The product controls VOCs through steam, gas, liquid, and bellows structures. Our company understands the need to accommodate various applications without being hindered by temperature or environmental factors. - The LowFlow series will be available in materials such as Monel, Hastelloy, Alloy 20, titanium, Kynar, and Inconel to meet your requirements. For more details, please contact us or download the catalog.

Complies with strict specifications for sterilization processes and clean utility systems. Usable in a wide range of applications such as biopharmaceuticals, injectable solutions, cosmetics, dairy products, food, and beverages.

The body and all wetted parts of the MK978 stainless steel control valve are made of ASTM A479-316L bar stock. The product is sealed at the stem by a Jorlon diaphragm that is FDA approved and USP Class VI certified, and comes with a lifetime warranty. The valve stem has sufficient structural strength in any mounting orientation due to two long PEEK guide bushings and an integrated stainless steel NAMUR yoke. The sliding parts of the valve stem and plug are located outside the diaphragm wetted area at the top of the valve. This product features a secondary stem seal and provides additional retention through extended guide bushings, ensuring self-drainage regardless of the mounting orientation. For more details, please contact us or download the catalog.

3A certified. Finish of the wetted parts: 32Ra/0.8μm.

FB6903 is necessary to protect products from backflow. The valve remains open due to the forward flow of fluid. If the flow is interrupted, the plug is pressed against the seat by a spring, closing the valve due to backflow. This valve is used in many sanitary applications and is a 3A certified product in accordance with the 58-01 standard.

Suitable for processes and cleaning equipment examples, food, beverages, dairy products, CIP, SIP, centrifuges, sterilization equipment, nitrogen gas control for blankets, etc.

FB5C operates by sensing the pressure or back pressure of the fluid supplied to the underside of the diaphragm from the side-mounted inlet. Back pressure above the set pressure compresses the spring through the load force of the diaphragm, causing the stem to function in an open state from the seat. As the flow increases and the back pressure is discharged, the forces from the spring and diaphragm are relieved, allowing the stem to return to its normally closed position. Changing the set pressure can be done simply by turning the adjustment screw to increase or decrease pressure within the range of the regulator spring settings.

Suitable for processes and cleaning equipment examples, food, beverages, dairy products, CIP, SIP, centrifuges, sterilization devices, nitrogen gas control for blankets, etc.

FB6C operates by sensing the pressure on the underside of the diaphragm on the downstream side of the seat. When the downstream pressure approaches the set pressure, the force exerted on the diaphragm overcomes the force of the setting spring, causing the plug to begin moving upward to close. This reduces the downstream pressure and maintains the set pressure. When the pressure on the underside of the diaphragm begins to drop, the spring force pushes the plug downward to open it, maintaining the set pressure.