[Analysis Case] Simultaneous Heating Analysis of Copper Plates and Solder by TDS

It is possible to evaluate degassing in an environment close to the actual process by bringing the materials into contact with each other.

last updated Mar 13, 2025

Angle-resolved HAXPES measurement

HAXPES: Hard X-ray Photoelectron Spectroscopy

last updated Mar 12, 2025

[Analysis Case] Component Analysis of Water Repellent Areas

TOF-SIMS enables wide-area imaging evaluation of multiple components.

last updated Mar 13, 2025

[Analysis Case] Shape Evaluation Based on O-Ring Usage History

Non-destructive observation and thickness distribution analysis of components is possible using X-ray CT.

last updated Mar 13, 2025

[Case Study] Quality Control through Surface Analysis

The surface adhesion components (such as polydimethylsiloxane) can be evaluated using TOF-SIMS.

last updated Mar 13, 2025

[Analysis Case] Measurement of Impurity Concentration on the Surface and Inside of SiC Substrates

Analysis of the substrate surface and interior is separated using ICP-MS and GDMS.

last updated Mar 13, 2025

[Analysis Case] Evaluation of Discoloration Causes in Ceramics

TOF-SIMS enables imaging of the discoloration causes of inorganic materials.

last updated Mar 13, 2025

[Analysis Case] Evaluation of the Distribution of Cleaning Components on Ceramic Surfaces

It is possible to visualize the distribution of cleaning components and evaluate the distribution in the depth direction.

last updated Mar 13, 2025

[Analysis Case] Evaluation of Wetting Properties of Ceramics

It is possible to analyze organic substances characteristic of hydrophilic and hydrophobic areas of inorganic materials.

last updated Mar 13, 2025

[Analysis Case] Impurity Analysis of FeCoNi Alloy

It is possible to simultaneously analyze 77 elements using GDMS.

last updated Mar 13, 2025

[Analysis Case] Organic Contamination Analysis of Materials

We will analyze trace amounts of organic contaminants adhered to the material using TD-GC/MS.

last updated Mar 13, 2025

[Analysis Case] Component Analysis of Additives in Rubber Products

We will conduct a comprehensive qualitative evaluation of vulcanization accelerators, aging inhibitors, lubricants, and other substances in rubber products.

last updated Mar 13, 2025

Contract analysis service for in situ measurement using X-ray CT.

It is possible to observe three-dimensional structures under heating/cooling and stress/compression load conditions.

last updated Mar 12, 2025

List of reliability tests

Reliability Test

last updated Mar 12, 2025

Differentiation of mass spectrometry methods for solid sample surfaces

It is effective to differentiate between the two methods according to the purpose components and the size of the imaging field.

last updated Mar 12, 2025

Evaluation avoiding duplication of Oji Peak by HAXPES.

Comparison of spectra obtained from Ga line (HAXPES) and Al line/Mg line (XPS) measurements.

last updated Mar 12, 2025

[Analysis Case] Analysis of α-Alumina (α-Al2O3) by TDS

Thermal desorption gas analysis of ceramics

last updated Mar 13, 2025

[Analysis Case] Evaluation of Glass Fiber Reinforced Plastic using X-ray CT and GC/MS

Evaluation of GFRP is possible according to the purpose.

last updated Mar 14, 2025

[Analysis Case] Investigation of the Causes of Yellowing in Polyurethane

By using PDA and MS in LC, it is possible to qualitatively analyze colored extracts.

last updated Mar 13, 2025

[Analysis Case] Qualitative and Structural Analysis of Resin (Synthetic Polymer)

Insights into molecular structure can be obtained through combined analysis using FT-IR and thermal decomposition GC/MS.

last updated Mar 13, 2025

Analysis of Corrosive Gases Emitted from Resin

Analysis of corrosive gases generated from resin.

last updated Mar 13, 2025

[Analysis Case] Binding State Mapping by XPS

It is possible to evaluate the distribution of surface contamination and surface treatment on samples with mm-order precision.

last updated Mar 13, 2025

[Analysis Case] Wide-area Quantitative Mapping using XPS

It is possible to evaluate the composition distribution in an area of up to 70×70mm.

last updated Mar 13, 2025

[Analysis Case] XPS Analysis of Metal Pipe Inner Wall Using Combined Cutting Processing

We provide one-stop solutions from sample cutting processing to investigating the causes of discoloration and corrosion.

last updated Mar 13, 2025

[Analysis Case] Outgassing Analysis of Resin for 3D Printers

High-sensitivity analysis of exhaust gas is possible with the gas concentration device.

last updated Mar 13, 2025

[Analysis Case] Evaluation of Metal Impurities in the Metal Film and Interface of the Device

Impurities in films and interfaces such as plating can be evaluated using TOF-SIMS.

last updated Jul 18, 2025

Observation of structural changes in metallic materials through tensile testing using in situ X-ray CT.

Capable of evaluating three-dimensional structural changes according to tensile stress.

last updated Jul 24, 2025

[Analysis Case] Composition Analysis of Particles on a Wafer

Shape observation and simple quantitative analysis using SEM-EDX.

last updated Aug 26, 2025